mem: Update DRAM configuration names

Names of DRAM configurations were updated to reflect both
the channel and device data width.

Previous naming format was:
<DEVICE_TYPE>_<DATA_RATE>_<CHANNEL_WIDTH>

The following nomenclature is now used:
<DEVICE_TYPE>_<DATA_RATE>_<n>x<w>
where n = The number of devices per rank on the channel
x = Device width

Total channel width can be calculated by n*w

Example:
A 64-bit DDR4, 2400 channel consisting of 4-bit devices:
n = 16
w = 4
The resulting configuration name is:
DDR4_2400_16x4

Updated scripts to match new naming convention.

Added unique configurations for DDR4 for:
1) 16x4
2) 8x8
3) 4x16

Change-Id: Ibd7f763b7248835c624309143cb9fc29d56a69d1
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
Reviewed-by: Curtis Dunham <curtis.dunham@arm.com>

config: Add a BaseSESystem builder for re-use in regressions

This patch extends the existing system builders to also include a
syscall-emulation builder. This builder is deployed in all
syscall-emulation regressions that do not involve Ruby,
i.e. o3-timing, simple-timing and simple-atomic, as well as the
multi-processor regressions o3-timing-mp, simple-timing-mp and
simple-atomic-mp (the latter are only used by SPARC at this point).

The values chosen for the cache sizes match those that were used in
the existing config scripts (despite being on the large
side). Similarly, a mem_class parameter is added to the builder base
class to enable simple-atomic to use SimpleMemory and o3-timing to use
the default DDR3 configuration.

Due to the different order the ports are connected, the bus stats get
shuffled around for the multi-processor regressions. A separate patch
bumps the port indices. Besides this, all behaviour is exactly the
same.

config: Add a system clock command-line option

This patch adds a 'sys_clock' command-line option and use it to assign
clocks to the system during instantiation.

As part of this change, the default clock in the System class is
removed and whenever a system is instantiated a system clock value
must be set. A default value is provided for the command-line option.

The configs and tests are updated accordingly.

mem: More descriptive DRAM config names

This patch changes the class names of the variuos DRAM configurations
to better reflect what memory they are based on. The speed and
interface width is now part of the name, and also the alias that is
used to select them on the command line.

Some minor changes are done to the actual parameters, to better
reflect the named configurations. As a result of these changes the
regressions change slightly and the stats will be bumped in a separate
patch.

mem: Add DDR3 and LPDDR2 DRAM controller configurations

This patch moves the default DRAM parameters from the SimpleDRAM class
to two different subclasses, one for DDR3 and one for LPDDR2. More can
be added as we go forward.

The regressions that previously used the SimpleDRAM are now using
SimpleDDR3 as this is the most similar configuration.

tests: Always specify memory mode in every test system.

Previous to this change we didn't always set the memory mode which worked as
long as we never attempted to switch CPUs or checked that a CPU was in a
memory system with the correct mode. Future changes will make CPUs verify
that they're operating in the correct mode and thus we need to always set it.

config: Unify caches used in regressions and adjust L2 MSHRs

This patch unified the L1 and L2 caches used throughout the
regressions instead of declaring different, but very similar,
configurations in the different scripts.

The patch also changes the default L2 configuration to match what it
used to be for the fs and se scripts (until the last patch that
updated the regressions to also make use of the cache config). The
MSHRs and targets per MSHR are now set to a more realistic default of
20 and 12, respectively.

As a result of both the aforementioned changes, many of the regression
stats are changed. A follow-on patch will bump the stats.

config: Use SimpleDRAM in full-system, and with o3 and inorder

This patch favours using SimpleDRAM with the default timing instead of
SimpleMemory for all regressions that involve the o3 or inorder CPU,
or are full system (in other words, where the actual performance of
the memory is important for the overall performance).

Moving forward, the solution for FSConfig and the users of fs.py and
se.py is probably something similar to what we use to choose the CPU
type. I envision a few pre-set configurations SimpleLPDDR2,
SimpleDDR3, etc that can be choosen by a dram_type option. Feedback on
this part is welcome.

This patch changes plenty stats and adds all the DRAM controller
related stats. A follow-on patch updates the relevant statistics. The
total run-time for the entire regression goes up with ~5% with this
patch due to the added complexity of the SimpleDRAM model. This is a
concious trade-off to ensure that the model is properly tested.

Mem: Use cycles to express cache-related latencies

This patch changes the cache-related latencies from an absolute time
expressed in Ticks, to a number of cycles that can be scaled with the
clock period of the caches. Ultimately this patch serves to enable
future work that involves dynamic frequency scaling. As an immediate
benefit it also makes it more convenient to specify cache performance
without implicitly assuming a specific CPU core operating frequency.

The stat blocked_cycles that actually counter in ticks is now updated
to count in cycles.

As the timing is now rounded to the clock edges of the cache, there
are some regressions that change. Plenty of them have very minor
changes, whereas some regressions with a short run-time are perturbed
quite significantly. A follow-on patch updates all the statistics for
the regressions.

Cache: add a response latency to the caches

In the current caches the hit latency is paid twice on a miss. This patch lets
a configurable response latency be set of the cache for the backward path.

Bus: Split the bus into a non-coherent and coherent bus

This patch introduces a class hierarchy of buses, a non-coherent one,
and a coherent one, splitting the existing bus functionality. By doing
so it also enables further specialisation of the two types of buses.

A non-coherent bus connects a number of non-snooping masters and
slaves, and routes the request and response packets based on the
address. The request packets issued by the master connected to a
non-coherent bus could still snoop in caches attached to a coherent
bus, as is the case with the I/O bus and memory bus in most system
configurations. No snoops will, however, reach any master on the
non-coherent bus itself. The non-coherent bus can be used as a
template for modelling PCI, PCIe, and non-coherent AMBA and OCP buses,
and is typically used for the I/O buses.

A coherent bus connects a number of (potentially) snooping masters and
slaves, and routes the request and response packets based on the
address, and also forwards all requests to the snoopers and deals with
the snoop responses. The coherent bus can be used as a template for
modelling QPI, HyperTransport, ACE and coherent OCP buses, and is
typically used for the L1-to-L2 buses and as the main system
interconnect.

The configuration scripts are updated to use a NoncoherentBus for all
peripheral and I/O buses.

A bit of minor tidying up has also been done.

MEM: Enable multiple distributed generalized memories

This patch removes the assumption on having on single instance of
PhysicalMemory, and enables a distributed memory where the individual
memories in the system are each responsible for a single contiguous
address range.

All memories inherit from an AbstractMemory that encompasses the basic
behaviuor of a random access memory, and provides untimed access
methods. What was previously called PhysicalMemory is now
SimpleMemory, and a subclass of AbstractMemory. All future types of
memory controllers should inherit from AbstractMemory.

To enable e.g. the atomic CPU and RubyPort to access the now
distributed memory, the system has a wrapper class, called
PhysicalMemory that is aware of all the memories in the system and
their associated address ranges. This class thus acts as an
infinitely-fast bus and performs address decoding for these "shortcut"
accesses. Each memory can specify that it should not be part of the
global address map (used e.g. by the functional memories by some
testers). Moreover, each memory can be configured to be reported to
the OS configuration table, useful for populating ATAG structures, and
any potential ACPI tables.

Checkpointing support currently assumes that all memories have the
same size and organisation when creating and resuming from the
checkpoint. A future patch will enable a more flexible
re-organisation.

CheckerCPU: Make some basic regression tests for CheckerCPU

Adds regression tests for the CheckerCPU. ARM ISA support
only at this point.