xbar.cc revision 9278
16019Shines@cs.fsu.edu/* 27399SAli.Saidi@ARM.com * Copyright (c) 2011-2012 ARM Limited 37399SAli.Saidi@ARM.com * All rights reserved 47399SAli.Saidi@ARM.com * 57399SAli.Saidi@ARM.com * The license below extends only to copyright in the software and shall 67399SAli.Saidi@ARM.com * not be construed as granting a license to any other intellectual 77399SAli.Saidi@ARM.com * property including but not limited to intellectual property relating 87399SAli.Saidi@ARM.com * to a hardware implementation of the functionality of the software 97399SAli.Saidi@ARM.com * licensed hereunder. You may use the software subject to the license 107399SAli.Saidi@ARM.com * terms below provided that you ensure that this notice is replicated 117399SAli.Saidi@ARM.com * unmodified and in its entirety in all distributions of the software, 127399SAli.Saidi@ARM.com * modified or unmodified, in source code or in binary form. 137399SAli.Saidi@ARM.com * 146019Shines@cs.fsu.edu * Copyright (c) 2006 The Regents of The University of Michigan 156019Shines@cs.fsu.edu * All rights reserved. 166019Shines@cs.fsu.edu * 176019Shines@cs.fsu.edu * Redistribution and use in source and binary forms, with or without 186019Shines@cs.fsu.edu * modification, are permitted provided that the following conditions are 196019Shines@cs.fsu.edu * met: redistributions of source code must retain the above copyright 206019Shines@cs.fsu.edu * notice, this list of conditions and the following disclaimer; 216019Shines@cs.fsu.edu * redistributions in binary form must reproduce the above copyright 226019Shines@cs.fsu.edu * notice, this list of conditions and the following disclaimer in the 236019Shines@cs.fsu.edu * documentation and/or other materials provided with the distribution; 246019Shines@cs.fsu.edu * neither the name of the copyright holders nor the names of its 256019Shines@cs.fsu.edu * contributors may be used to endorse or promote products derived from 266019Shines@cs.fsu.edu * this software without specific prior written permission. 276019Shines@cs.fsu.edu * 286019Shines@cs.fsu.edu * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 296019Shines@cs.fsu.edu * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 306019Shines@cs.fsu.edu * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 316019Shines@cs.fsu.edu * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 326019Shines@cs.fsu.edu * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 336019Shines@cs.fsu.edu * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 346019Shines@cs.fsu.edu * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 356019Shines@cs.fsu.edu * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 366019Shines@cs.fsu.edu * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 376019Shines@cs.fsu.edu * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 386019Shines@cs.fsu.edu * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 396019Shines@cs.fsu.edu * 407399SAli.Saidi@ARM.com * Authors: Ali Saidi 416019Shines@cs.fsu.edu * Andreas Hansson 426019Shines@cs.fsu.edu * William Wang 436019Shines@cs.fsu.edu */ 446019Shines@cs.fsu.edu 456019Shines@cs.fsu.edu/** 466019Shines@cs.fsu.edu * @file 476019Shines@cs.fsu.edu * Definition of a bus object. 486019Shines@cs.fsu.edu */ 496019Shines@cs.fsu.edu 506019Shines@cs.fsu.edu#include "base/misc.hh" 516019Shines@cs.fsu.edu#include "base/trace.hh" 526019Shines@cs.fsu.edu#include "debug/Bus.hh" 536019Shines@cs.fsu.edu#include "debug/BusAddrRanges.hh" 546116Snate@binkert.org#include "debug/Drain.hh" 556019Shines@cs.fsu.edu#include "mem/bus.hh" 566019Shines@cs.fsu.edu 576019Shines@cs.fsu.eduBaseBus::BaseBus(const BaseBusParams *p) 586019Shines@cs.fsu.edu : MemObject(p), 596019Shines@cs.fsu.edu headerCycles(p->header_cycles), width(p->width), 606019Shines@cs.fsu.edu defaultPortID(InvalidPortID), 616019Shines@cs.fsu.edu useDefaultRange(p->use_default_range), 627404SAli.Saidi@ARM.com blockSize(p->block_size) 637404SAli.Saidi@ARM.com{} 646019Shines@cs.fsu.edu 656019Shines@cs.fsu.eduBaseBus::~BaseBus() 667294Sgblack@eecs.umich.edu{ 677294Sgblack@eecs.umich.edu for (MasterPortIter m = masterPorts.begin(); m != masterPorts.end(); 687639Sgblack@eecs.umich.edu ++m) { 697294Sgblack@eecs.umich.edu delete *m; 707294Sgblack@eecs.umich.edu } 717294Sgblack@eecs.umich.edu 727294Sgblack@eecs.umich.edu for (SlavePortIter s = slavePorts.begin(); s != slavePorts.end(); 737294Sgblack@eecs.umich.edu ++s) { 747639Sgblack@eecs.umich.edu delete *s; 757639Sgblack@eecs.umich.edu } 767294Sgblack@eecs.umich.edu} 777639Sgblack@eecs.umich.edu 787404SAli.Saidi@ARM.comvoid 797639Sgblack@eecs.umich.eduBaseBus::init() 807294Sgblack@eecs.umich.edu{ 817294Sgblack@eecs.umich.edu // determine the maximum peer block size, look at both the 827294Sgblack@eecs.umich.edu // connected master and slave modules 837639Sgblack@eecs.umich.edu uint32_t peer_block_size = 0; 847294Sgblack@eecs.umich.edu 856019Shines@cs.fsu.edu for (MasterPortConstIter m = masterPorts.begin(); m != masterPorts.end(); 866019Shines@cs.fsu.edu ++m) { 876019Shines@cs.fsu.edu peer_block_size = std::max((*m)->peerBlockSize(), peer_block_size); 886019Shines@cs.fsu.edu } 897404SAli.Saidi@ARM.com 906019Shines@cs.fsu.edu for (SlavePortConstIter s = slavePorts.begin(); s != slavePorts.end(); 916019Shines@cs.fsu.edu ++s) { 927406SAli.Saidi@ARM.com peer_block_size = std::max((*s)->peerBlockSize(), peer_block_size); 937436Sdam.sunwoo@arm.com } 947436Sdam.sunwoo@arm.com 957406SAli.Saidi@ARM.com // if the peers do not have a block size, use the default value 967404SAli.Saidi@ARM.com // set through the bus parameters 977406SAli.Saidi@ARM.com if (peer_block_size != 0) 986019Shines@cs.fsu.edu blockSize = peer_block_size; 996019Shines@cs.fsu.edu 1007404SAli.Saidi@ARM.com // check if the block size is a value known to work 1016019Shines@cs.fsu.edu if (blockSize != 16 || blockSize != 32 || blockSize != 64 || 1027399SAli.Saidi@ARM.com blockSize != 128) 1036020Sgblack@eecs.umich.edu warn_once("Block size is neither 16, 32, 64 or 128 bytes.\n"); 1046020Sgblack@eecs.umich.edu} 1056020Sgblack@eecs.umich.edu 1066020Sgblack@eecs.umich.eduMasterPort & 1076020Sgblack@eecs.umich.eduBaseBus::getMasterPort(const std::string &if_name, int idx) 1086020Sgblack@eecs.umich.edu{ 1096020Sgblack@eecs.umich.edu if (if_name == "master" && idx < masterPorts.size()) { 1106020Sgblack@eecs.umich.edu // the master port index translates directly to the vector position 1116019Shines@cs.fsu.edu return *masterPorts[idx]; 1126019Shines@cs.fsu.edu } else if (if_name == "default") { 1136019Shines@cs.fsu.edu return *masterPorts[defaultPortID]; 1146019Shines@cs.fsu.edu } else { 1157404SAli.Saidi@ARM.com return MemObject::getMasterPort(if_name, idx); 1166019Shines@cs.fsu.edu } 1176019Shines@cs.fsu.edu} 1186019Shines@cs.fsu.edu 1196019Shines@cs.fsu.eduSlavePort & 1206019Shines@cs.fsu.eduBaseBus::getSlavePort(const std::string &if_name, int idx) 1216019Shines@cs.fsu.edu{ 1226019Shines@cs.fsu.edu if (if_name == "slave" && idx < slavePorts.size()) { 1237404SAli.Saidi@ARM.com // the slave port index translates directly to the vector position 1247404SAli.Saidi@ARM.com return *slavePorts[idx]; 1257404SAli.Saidi@ARM.com } else { 1266019Shines@cs.fsu.edu return MemObject::getSlavePort(if_name, idx); 1277404SAli.Saidi@ARM.com } 1287404SAli.Saidi@ARM.com} 1297404SAli.Saidi@ARM.com 1307404SAli.Saidi@ARM.comTick 1317404SAli.Saidi@ARM.comBaseBus::calcPacketTiming(PacketPtr pkt) 1327404SAli.Saidi@ARM.com{ 1337404SAli.Saidi@ARM.com // determine the current time rounded to the closest following 1347404SAli.Saidi@ARM.com // clock edge 1357404SAli.Saidi@ARM.com Tick now = nextCycle(); 1367404SAli.Saidi@ARM.com 1377404SAli.Saidi@ARM.com Tick headerTime = now + headerCycles * clock; 1387404SAli.Saidi@ARM.com 1397404SAli.Saidi@ARM.com // The packet will be sent. Figure out how long it occupies the bus, and 1407404SAli.Saidi@ARM.com // how much of that time is for the first "word", aka bus width. 1417404SAli.Saidi@ARM.com int numCycles = 0; 1427404SAli.Saidi@ARM.com if (pkt->hasData()) { 1437404SAli.Saidi@ARM.com // If a packet has data, it needs ceil(size/width) cycles to send it 1447404SAli.Saidi@ARM.com int dataSize = pkt->getSize(); 1457406SAli.Saidi@ARM.com numCycles += dataSize/width; 1467406SAli.Saidi@ARM.com if (dataSize % width) 1477404SAli.Saidi@ARM.com numCycles++; 1487404SAli.Saidi@ARM.com } 1497404SAli.Saidi@ARM.com 1506019Shines@cs.fsu.edu // The first word will be delivered after the current tick, the delivery 1516019Shines@cs.fsu.edu // of the address if any, and one bus cycle to deliver the data 1527404SAli.Saidi@ARM.com pkt->firstWordTime = headerTime + clock; 1536019Shines@cs.fsu.edu 1546019Shines@cs.fsu.edu pkt->finishTime = headerTime + numCycles * clock; 1556019Shines@cs.fsu.edu 1566019Shines@cs.fsu.edu return headerTime; 1577436Sdam.sunwoo@arm.com} 1587436Sdam.sunwoo@arm.com 1597436Sdam.sunwoo@arm.comtemplate <typename PortClass> 1607436Sdam.sunwoo@arm.comBaseBus::Layer<PortClass>::Layer(BaseBus& _bus, const std::string& _name, 1617436Sdam.sunwoo@arm.com Tick _clock) : 1627436Sdam.sunwoo@arm.com bus(_bus), _name(_name), state(IDLE), clock(_clock), drainEvent(NULL), 1637436Sdam.sunwoo@arm.com releaseEvent(this) 1647436Sdam.sunwoo@arm.com{ 1657436Sdam.sunwoo@arm.com} 1667436Sdam.sunwoo@arm.com 1677436Sdam.sunwoo@arm.comtemplate <typename PortClass> 1687436Sdam.sunwoo@arm.comvoid BaseBus::Layer<PortClass>::occupyLayer(Tick until) 1697436Sdam.sunwoo@arm.com{ 1707404SAli.Saidi@ARM.com // ensure the state is busy or in retry and never idle at this 1717404SAli.Saidi@ARM.com // point, as the bus should transition from idle as soon as it has 1727404SAli.Saidi@ARM.com // decided to forward the packet to prevent any follow-on calls to 1737404SAli.Saidi@ARM.com // sendTiming seeing an unoccupied bus 1747404SAli.Saidi@ARM.com assert(state != IDLE); 1757404SAli.Saidi@ARM.com 1767404SAli.Saidi@ARM.com // note that we do not change the bus state here, if we are going 1776116Snate@binkert.org // from idle to busy it is handled by tryTiming, and if we 1787404SAli.Saidi@ARM.com // are in retry we should remain in retry such that 1796116Snate@binkert.org // succeededTiming still sees the accurate state 1806116Snate@binkert.org 1816019Shines@cs.fsu.edu // until should never be 0 as express snoops never occupy the bus 1826019Shines@cs.fsu.edu assert(until != 0); 1836019Shines@cs.fsu.edu bus.schedule(releaseEvent, until); 1846019Shines@cs.fsu.edu 1856019Shines@cs.fsu.edu DPRINTF(BaseBus, "The bus is now busy from tick %d to %d\n", 1866019Shines@cs.fsu.edu curTick(), until); 1876019Shines@cs.fsu.edu} 1886116Snate@binkert.org 1896019Shines@cs.fsu.edutemplate <typename PortClass> 1906019Shines@cs.fsu.edubool 191BaseBus::Layer<PortClass>::tryTiming(PortClass* port) 192{ 193 // first we see if the bus is busy, next we check if we are in a 194 // retry with a port other than the current one 195 if (state == BUSY || (state == RETRY && port != retryList.front())) { 196 // put the port at the end of the retry list 197 retryList.push_back(port); 198 return false; 199 } 200 201 // update the state which is shared for request, response and 202 // snoop responses, if we were idle we are now busy, if we are in 203 // a retry, then do not change 204 if (state == IDLE) 205 state = BUSY; 206 207 return true; 208} 209 210template <typename PortClass> 211void 212BaseBus::Layer<PortClass>::succeededTiming(Tick busy_time) 213{ 214 // if a retrying port succeeded, also take it off the retry list 215 if (state == RETRY) { 216 DPRINTF(BaseBus, "Remove retry from list %s\n", 217 retryList.front()->name()); 218 retryList.pop_front(); 219 state = BUSY; 220 } 221 222 // we should either have gone from idle to busy in the 223 // tryTiming test, or just gone from a retry to busy 224 assert(state == BUSY); 225 226 // occupy the bus accordingly 227 occupyLayer(busy_time); 228} 229 230template <typename PortClass> 231void 232BaseBus::Layer<PortClass>::failedTiming(PortClass* port, Tick busy_time) 233{ 234 // if we are not in a retry, i.e. busy (but never idle), or we are 235 // in a retry but not for the current port, then add the port at 236 // the end of the retry list 237 if (state != RETRY || port != retryList.front()) { 238 retryList.push_back(port); 239 } 240 241 // even if we retried the current one and did not succeed, 242 // we are no longer retrying but instead busy 243 state = BUSY; 244 245 // occupy the bus accordingly 246 occupyLayer(busy_time); 247} 248 249template <typename PortClass> 250void 251BaseBus::Layer<PortClass>::releaseLayer() 252{ 253 // releasing the bus means we should now be idle 254 assert(state == BUSY); 255 assert(!releaseEvent.scheduled()); 256 257 // update the state 258 state = IDLE; 259 260 // bus is now idle, so if someone is waiting we can retry 261 if (!retryList.empty()) { 262 // note that we block (return false on recvTiming) both 263 // because the bus is busy and because the destination is 264 // busy, and in the latter case the bus may be released before 265 // we see a retry from the destination 266 retryWaiting(); 267 } else if (drainEvent) { 268 DPRINTF(Drain, "Bus done draining, processing drain event\n"); 269 //If we weren't able to drain before, do it now. 270 drainEvent->process(); 271 // Clear the drain event once we're done with it. 272 drainEvent = NULL; 273 } 274} 275 276template <typename PortClass> 277void 278BaseBus::Layer<PortClass>::retryWaiting() 279{ 280 // this should never be called with an empty retry list 281 assert(!retryList.empty()); 282 283 // we always go to retrying from idle 284 assert(state == IDLE); 285 286 // update the state which is shared for request, response and 287 // snoop responses 288 state = RETRY; 289 290 // note that we might have blocked on the receiving port being 291 // busy (rather than the bus itself) and now call retry before the 292 // destination called retry on the bus 293 retryList.front()->sendRetry(); 294 295 // If the bus is still in the retry state, sendTiming wasn't 296 // called in zero time (e.g. the cache does this) 297 if (state == RETRY) { 298 retryList.pop_front(); 299 300 //Burn a cycle for the missed grant. 301 302 // update the state which is shared for request, response and 303 // snoop responses 304 state = BUSY; 305 306 // determine the current time rounded to the closest following 307 // clock edge 308 Tick now = bus.nextCycle(); 309 310 occupyLayer(now + clock); 311 } 312} 313 314template <typename PortClass> 315void 316BaseBus::Layer<PortClass>::recvRetry() 317{ 318 // we got a retry from a peer that we tried to send something to 319 // and failed, but we sent it on the account of someone else, and 320 // that source port should be on our retry list, however if the 321 // bus layer is released before this happens and the retry (from 322 // the bus point of view) is successful then this no longer holds 323 // and we could in fact have an empty retry list 324 if (retryList.empty()) 325 return; 326 327 // if the bus layer is idle 328 if (state == IDLE) { 329 // note that we do not care who told us to retry at the moment, we 330 // merely let the first one on the retry list go 331 retryWaiting(); 332 } 333} 334 335PortID 336BaseBus::findPort(Addr addr) 337{ 338 /* An interval tree would be a better way to do this. --ali. */ 339 PortID dest_id = checkPortCache(addr); 340 if (dest_id != InvalidPortID) 341 return dest_id; 342 343 // Check normal port ranges 344 PortMapConstIter i = portMap.find(RangeSize(addr,1)); 345 if (i != portMap.end()) { 346 dest_id = i->second; 347 updatePortCache(dest_id, i->first.start, i->first.end); 348 return dest_id; 349 } 350 351 // Check if this matches the default range 352 if (useDefaultRange) { 353 AddrRangeConstIter a_end = defaultRange.end(); 354 for (AddrRangeConstIter i = defaultRange.begin(); i != a_end; i++) { 355 if (*i == addr) { 356 DPRINTF(BusAddrRanges, " found addr %#llx on default\n", 357 addr); 358 return defaultPortID; 359 } 360 } 361 } else if (defaultPortID != InvalidPortID) { 362 DPRINTF(BusAddrRanges, "Unable to find destination for addr %#llx, " 363 "will use default port\n", addr); 364 return defaultPortID; 365 } 366 367 // we should use the range for the default port and it did not 368 // match, or the default port is not set 369 fatal("Unable to find destination for addr %#llx on bus %s\n", addr, 370 name()); 371} 372 373/** Function called by the port when the bus is receiving a range change.*/ 374void 375BaseBus::recvRangeChange(PortID master_port_id) 376{ 377 AddrRangeIter iter; 378 379 if (inRecvRangeChange.count(master_port_id)) 380 return; 381 inRecvRangeChange.insert(master_port_id); 382 383 DPRINTF(BusAddrRanges, "received RangeChange from device id %d\n", 384 master_port_id); 385 386 clearPortCache(); 387 if (master_port_id == defaultPortID) { 388 defaultRange.clear(); 389 // Only try to update these ranges if the user set a default responder. 390 if (useDefaultRange) { 391 // get the address ranges of the connected slave port 392 AddrRangeList ranges = 393 masterPorts[master_port_id]->getAddrRanges(); 394 for(iter = ranges.begin(); iter != ranges.end(); iter++) { 395 defaultRange.push_back(*iter); 396 DPRINTF(BusAddrRanges, "Adding range %#llx - %#llx for default range\n", 397 iter->start, iter->end); 398 } 399 } 400 } else { 401 402 assert(master_port_id < masterPorts.size() && master_port_id >= 0); 403 MasterPort *port = masterPorts[master_port_id]; 404 405 // Clean out any previously existent ids 406 for (PortMapIter portIter = portMap.begin(); 407 portIter != portMap.end(); ) { 408 if (portIter->second == master_port_id) 409 portMap.erase(portIter++); 410 else 411 portIter++; 412 } 413 414 // get the address ranges of the connected slave port 415 AddrRangeList ranges = port->getAddrRanges(); 416 417 for (iter = ranges.begin(); iter != ranges.end(); iter++) { 418 DPRINTF(BusAddrRanges, "Adding range %#llx - %#llx for id %d\n", 419 iter->start, iter->end, master_port_id); 420 if (portMap.insert(*iter, master_port_id) == portMap.end()) { 421 PortID conflict_id = portMap.find(*iter)->second; 422 fatal("%s has two ports with same range:\n\t%s\n\t%s\n", 423 name(), 424 masterPorts[master_port_id]->getSlavePort().name(), 425 masterPorts[conflict_id]->getSlavePort().name()); 426 } 427 } 428 } 429 DPRINTF(BusAddrRanges, "port list has %d entries\n", portMap.size()); 430 431 // tell all our neighbouring master ports that our address range 432 // has changed 433 for (SlavePortConstIter p = slavePorts.begin(); p != slavePorts.end(); 434 ++p) 435 (*p)->sendRangeChange(); 436 437 inRecvRangeChange.erase(master_port_id); 438} 439 440AddrRangeList 441BaseBus::getAddrRanges() const 442{ 443 AddrRangeList ranges; 444 445 DPRINTF(BusAddrRanges, "received address range request, returning:\n"); 446 447 for (AddrRangeConstIter dflt_iter = defaultRange.begin(); 448 dflt_iter != defaultRange.end(); dflt_iter++) { 449 ranges.push_back(*dflt_iter); 450 DPRINTF(BusAddrRanges, " -- Dflt: %#llx : %#llx\n",dflt_iter->start, 451 dflt_iter->end); 452 } 453 for (PortMapConstIter portIter = portMap.begin(); 454 portIter != portMap.end(); portIter++) { 455 bool subset = false; 456 for (AddrRangeConstIter dflt_iter = defaultRange.begin(); 457 dflt_iter != defaultRange.end(); dflt_iter++) { 458 if ((portIter->first.start < dflt_iter->start && 459 portIter->first.end >= dflt_iter->start) || 460 (portIter->first.start < dflt_iter->end && 461 portIter->first.end >= dflt_iter->end)) 462 fatal("Devices can not set ranges that itersect the default set\ 463 but are not a subset of the default set.\n"); 464 if (portIter->first.start >= dflt_iter->start && 465 portIter->first.end <= dflt_iter->end) { 466 subset = true; 467 DPRINTF(BusAddrRanges, " -- %#llx : %#llx is a SUBSET\n", 468 portIter->first.start, portIter->first.end); 469 } 470 } 471 if (!subset) { 472 ranges.push_back(portIter->first); 473 DPRINTF(BusAddrRanges, " -- %#llx : %#llx\n", 474 portIter->first.start, portIter->first.end); 475 } 476 } 477 478 return ranges; 479} 480 481unsigned 482BaseBus::deviceBlockSize() const 483{ 484 return blockSize; 485} 486 487template <typename PortClass> 488unsigned int 489BaseBus::Layer<PortClass>::drain(Event * de) 490{ 491 //We should check that we're not "doing" anything, and that noone is 492 //waiting. We might be idle but have someone waiting if the device we 493 //contacted for a retry didn't actually retry. 494 if (!retryList.empty() || state != IDLE) { 495 DPRINTF(Drain, "Bus not drained\n"); 496 drainEvent = de; 497 return 1; 498 } 499 return 0; 500} 501 502/** 503 * Bus layer template instantiations. Could be removed with _impl.hh 504 * file, but since there are only two given options (MasterPort and 505 * SlavePort) it seems a bit excessive at this point. 506 */ 507template class BaseBus::Layer<SlavePort>; 508template class BaseBus::Layer<MasterPort>; 509